Every natural stone carving has features a moulded product would be rejected for. That is not a quality problem — it is what "natural" means, and it is why a carved piece costs what it does.

The difficulty is that buyers and suppliers often use the same three words — flaw, inclusion, crack — to mean different things, and nobody defines them before production. That is where disputes come from. Not usually from a bad piece, but from a piece that one side considers normal and the other considers broken.

This is a practical attempt to separate the categories, and to say where the line usually falls.

Four categories, not two

Most arguments happen because a buyer has a binary in mind: acceptable or faulty. Stone features split more usefully into four groups, because each carries a different obligation.

1. Inherent features. Characteristics of the material itself: colour banding, veining, drusy pockets, natural inclusions, a mineral's own internal structure. Labradorite's colour play, the banding in agate, the fibrous sheen of tiger eye — these are the reasons those materials are chosen. No two pieces are alike, and one piece cannot be matched exactly to another.

2. Working features. Marks that come from the material meeting the carving process: a small natural pit revealed as material was removed, a healed fracture that the carving crossed, a variation in polish where the stone's hardness changes across the piece. These are unavoidable in a made object of natural material. They are normally acceptable.

3. Defects. Genuine failures of specification or workmanship. A fracture caused by mishandling. A chip on a visible edge. A piece carved off-centre. A material substitution. A surface so under-polished it does not match the finish agreed. These are the supplier's responsibility.

4. Damage. Defects that occur after production — usually in packing or transit. A separate category because responsibility is different, and because it is often mistaken for a defect in the making. See packaging crystal skulls for shipping.

The practical test for categories 1 to 3 is one question: did this feature exist in the raw material, or did our process put it there? A pit that followed the stone is inherent. A pit that followed a chisel is a defect.

There is a related distinction that causes almost as much trouble: variation between batches rather than within a piece. A repeat order cut from a different block will differ in colour and pattern while every individual piece is sound — which is not a defect at all. Reordering carved stone sets out that difference and how to specify a tolerance for it.

Where buyers and suppliers usually disagree

Three specific cases account for most disputes. It is worth agreeing on them before an order rather than after.

Cracks: "healed" versus "open"

This is the single most common argument in carved stone.

A healed fracture is a plane inside the stone where it broke in the mountain and re-cemented over geological time. The material on both sides is continuous; the line is a colour or clarity difference. A carving can be structurally sound across a healed fracture, and many fine pieces contain them. They are inherent.

An open fracture is a discontinuity. It may be a hairline with no gap, or a visible break. Under finger pressure, or a tap with a coin, an open fracture has movement or a dull sound where the surrounding stone rings.

The two can look similar in a photograph. This is why "is that crack a problem?" is a question photographs usually cannot answer, and why we will tell a buyer when we cannot judge a feature from an image.

What matters is not only whether it is open, but where it is and how big it is relative to the piece. A hairline on the base of a 12 cm carving is a different commercial question from a hairline across the face of the same piece. Both may be inherent. Only one affects how the piece sells.

Pits, vugs and inclusions

A small cavity in the surface is normal in many materials, particularly agate, jasper and moss agate. A drusy pocket — a cluster of tiny crystals in a void — is often considered a feature, and in some materials buyers pay more for it.

The judgement is about prominence and placement, not existence. A 2 mm pit on the underside is not the same as a pit on the cheekbone of a skull where a retail customer will see it first.

Be sceptical of any supplier who claims a material has no pits at all. With agates and jaspers, that claim is usually a sign they have not looked, or are not being straight with you.

Colour and pattern that does not match the sample

Natural materials vary between blocks. A photograph of one piece is not a specification for the next one.

If a buyer approves a sample and then expects production to match it exactly, the order will fail — not because the supplier made a mistake, but because the expectation was impossible. The correct agreement is about range, not identity: this colour family, this pattern density, this characteristic range. See how to compare stone suppliers for how to write that into a comparison.

What is genuinely never acceptable

It is worth stating the other direction, because a "natural variation" defence can be stretched to cover things it should not.

None of the following are natural features, whatever the material:

  • A chip or fracture from handling after the piece was finished
  • A filled or dyed repair presented as natural stone without disclosure
  • A material substitution — tiger eye sold that is not tiger eye
  • A finish that does not match what was agreed
  • Dimensions outside the agreed tolerance
  • A crack that was filled and not mentioned

The last one is worth emphasis. Filling a crack is not automatically dishonest — stabilising a fragile piece can be legitimate work. Doing it silently is the problem. A buyer who will not disclose a filled repair is a buyer you cannot plan around.

Deciding who pays

Natural features sit with the buyer. Defects sit with the supplier. Damage in transit sits with whoever arranged and agreed that leg.

That sounds clear until you ask what happens on the boundary, so here is a practical way to settle it: agree the standard before production, in writing, in terms of visible outcome.

"First quality" and "no flaws" are not standards — nobody can apply them consistently. A standard looks like this:

  • Inclusions and healed fractures are acceptable on the base and sides
  • On the front face, features are acceptable up to the size of a grain of rice at arm's length under normal retail lighting
  • No open fractures anywhere
  • No filled or repaired areas without written disclosure before dispatch
  • Dimensions within ±2 mm of the agreed figure
  • Finish uniform across all visible surfaces

That is a standard two people can check independently and reach the same answer about. It is also the standard a third party can arbitrate against. Vague language cannot be arbitrated.

If a supplier is unwilling to put a standard like this in writing, that reluctance is itself information. See verifying a stone carving supplier.

What to actually do about it

Five measures cover most of the exposure.

Put the standard in the purchase order, before production. Not in the email thread, not in the chat. In the document both sides sign.

Photograph the finished piece before packing, from several angles, including the base. This establishes what left the workshop. It is also the only way to tell a manufacturing defect from transit damage later — without a pre-packing photograph, that distinction cannot be made at all.

Inspect against the standard, not against a feeling. Inspecting a stone carving order covers the process. The point here is that an inspector needs the written standard, or they will invent one.

Keep samples of the agreed finish. A physical reference ends finish arguments immediately. A photograph of a polished surface does not, because a photograph of stone tells you less about surface than you think.

Decide the policy for a feature, not the piece. When a piece does not clear the standard, agree in advance whether it is rejected, replaced, credited or accepted at a discount — and at what proportion. Deciding this while annoyed, mid-container, costs more than deciding it in advance.

Why we photograph the flaws

There is a temptation for a supplier to photograph a carving so that the good face is visible and the rest is not. It sells better. It also produces exactly the dispute described above, because the buyer's standard and the supplier's photographs were never compatible.

We photograph our pieces from multiple angles including the base, and for custom work we photograph the finished carving before packing. When we cannot determine whether a feature is a healed fracture or an open one from a photograph, we say so rather than guess — the piece may need to be looked at in person, and we would rather tell you that at the quotation stage than after you have paid.

If a material's identity, origin or treatment has not been confirmed from supplier records, we mark it as pending. You will find that on our own product pages. The same honesty applies to condition: a feature we have not determined, we describe as undetermined rather than call it natural.

If you are working to a written standard and want to know whether a specific material can meet it, send us the spec or see the materials we carve. We would rather tell you a material will not do something before you order than explain afterwards why it did not.